Go Back   AudiForums.com > Audi Models > Audi A4


Reply
 
Thread Tools
  #1  
Old 05-25-2007, 06:32 PM
kpatz kpatz is offline
 
Join Date: Mar 2006
Location:
Posts: 258
Default Got turbo replaced, now only getting 1300 mbar boost... *SOLVED*

Just picked my car up from the shop. I switched to APR 1+ chipped mode, but the car felt stock, if that. It drove smooth and fine, and it was boosting some, but not much. I was thinking limp mode, so when I got it home I scanned with vag-com, and there were no codes. I then logged requested vs. actual, and even when requested exceeded 2200, actual never went above 1300 or so.

I called the shop and they said they checked for vacuum and boost leaks and found none. They also said I would hear a boost leak, but I don't. Could it be something to do with the wastegate actuator or N75?

I'll be bringing the car back on Tuesday, but in the meantime if there's something simple to check, I will. I already checked the N75 hookups to make sure they were correct. The long nub goes into the TIP, the nub opposite the long one to the wastegate, and the remaining one into the turbo.

Here's a log of 115 (requested vs. actual) and 119 (N75 duty cycle): http://www.patzcatz.com/audi/log-01-115-119-xxx.csv

Thanks again...
__________________
2002 A4(B6) 1.8TQM, Goodwood Green
Mods: APR Stage 1+, TT225, 710N, APR Snub, JH solid short-throw shifter, Euro shift knob/boot, VMR 18" RS4 Reps w/General Exclaim UHP, 4300K HID D2S, hardwired Valentine 1 w/remote display


Reply With Quote
Sponsored Links
This ad is not displayed to registered members.
Register your free account today and become a member on Audi Forums!
  #2  
Old 05-25-2007, 06:38 PM
techbod techbod is offline
 
Join Date: Nov 2005
Location:
Posts: 12,830
Default RE: Got turbo replaced, now only getting 1300 mbar boost...

not my area but it does seem like the vac pipes are crossed one can only try
Reply With Quote
  #3  
Old 05-25-2007, 08:28 PM
david9999 david9999 is offline
Site Moderator
 
Join Date: Jul 2004
Location:
Posts: 4,327
Default RE: Got turbo replaced, now only getting 1300 mbar boost...

Not sure why they would be around the N75 for replacing the turbo. Sure doesn't look good.

My K03 runs at 2.1-2.2 and logging shows right pressures with the ECS N75 race valve.
__________________
2000 A4 1.8T Quattro tip
APR 93 chip
710N
ECS N75 Race Valve
Tip Chip
Borla Exhaust
Sports Suspension
Cracked windshield (again), 3rd timing belt
Reply With Quote
  #4  
Old 05-25-2007, 10:17 PM
kpatz kpatz is offline
 
Join Date: Mar 2006
Location:
Posts: 258
Default RE: Got turbo replaced, now only getting 1300 mbar boost...

The N75 is on the TIP and has two vac lines going to the turbo housing and wastegate actuator. So it would be touched. I verified it was hooked up correctly. Maybe some shavings from the old turbo got into it and messed it up.
__________________
2002 A4(B6) 1.8TQM, Goodwood Green
Mods: APR Stage 1+, TT225, 710N, APR Snub, JH solid short-throw shifter, Euro shift knob/boot, VMR 18" RS4 Reps w/General Exclaim UHP, 4300K HID D2S, hardwired Valentine 1 w/remote display


Reply With Quote
  #5  
Old 05-25-2007, 10:33 PM
fahquad fahquad is offline
 
Join Date: Apr 2007
Location:
Posts: 287
Default RE: Got turbo replaced, now only getting 1300 mbar boost...

Go to a4mods.com and check out his easy and cheap boost leak tester. Of course the usual check your hose connections disclaimer that everyone says "Duh" on. On the B6, leaks always seem to occur at the scution jet pump. But your requested vs. actual (based on what you say as I haven't opened the logs) is much bigger than what that would cause.
On mine, I had about the same thing. Requested was max that VAG COM would show, but I was maybe getting to 1400 and real late in the RPM range at that. Checked everywhere for boost leaks. No leaks. Ended up finding out that wastegate actuator was stuck open. So, maybe check that.
Hope you find it. Many leaks actually can't be heard and some can't be seen. Cracks in hoses only opens up under boost and you'd only see that under boost test.
Let us know!
[align=left] [/align]
Reply With Quote
  #6  
Old 05-25-2007, 11:06 PM
kpatz kpatz is offline
 
Join Date: Mar 2006
Location:
Posts: 258
Default RE: Got turbo replaced, now only getting 1300 mbar boost...

It seems to boost normally, it just tops off at 1350 or so, with requested being near 2400 during a WOT run.

If it were a boost leak, I would think it would be more inconsistent, or I would hear something, or the car wouldn't run right, or a code would be thrown. The car runs great, acceleration is smooth as silk, except for the lack of more than a minimal amount of boost.

If the wastegate were stuck open, it would spool up slowly. It spools up as quick as my old turbo did, it just maxes out at 1350 and holds. So that seems to point at the N75. I'll test it tomorrow.

__________________
2002 A4(B6) 1.8TQM, Goodwood Green
Mods: APR Stage 1+, TT225, 710N, APR Snub, JH solid short-throw shifter, Euro shift knob/boot, VMR 18" RS4 Reps w/General Exclaim UHP, 4300K HID D2S, hardwired Valentine 1 w/remote display


Reply With Quote
  #7  
Old 05-26-2007, 12:41 AM
The Bishop's Avatar
The Bishop The Bishop is offline
Senior Member
 
Join Date: Sep 2006
Location: Aspen
Posts: 1,014
Default RE: Got turbo replaced, now only getting 1300 mbar boost...

Check the vac hose from the intake manifold to the dv, it could have been damaged when they were working on the turbo oulet pipe. (those vac lines will crack apart).
__________________
Reply With Quote
  #8  
Old 05-26-2007, 02:43 PM
kpatz kpatz is offline
 
Join Date: Mar 2006
Location:
Posts: 258
Default RE: Got turbo replaced, now only getting 1300 mbar boost...

I pulled my N75 valve and tested it. It was clogged. After a few "suck-blow" cycles[:-] it freed up and it's working fine now.

I'll have to log again to see where my boost is, it seems a bit lower than what I remember stage 1+ being, but I haven't been on the highway yet to do a good run.
__________________
2002 A4(B6) 1.8TQM, Goodwood Green
Mods: APR Stage 1+, TT225, 710N, APR Snub, JH solid short-throw shifter, Euro shift knob/boot, VMR 18" RS4 Reps w/General Exclaim UHP, 4300K HID D2S, hardwired Valentine 1 w/remote display


Reply With Quote
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump

Advertising

Featured Sponsors


New Sponsors
AMSOIL - Performance Oil Technology
K&N Engineering
All times are GMT -4. The time now is 04:03 PM.

© Internet Brands, Inc.
Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.