Hey everyone, I'm in the process of doing a front bumper swap from my oem a4 front to an oem rs4 front. Ive searched and asked afew heads, but havent really found what i was looking for. Is there a thread that Ive missed or over looked that has a parts list and DIY guide like this page, A4 to S4, for the A4 to RS4? I know someones got a list and i really need it so i can know and understand exactly what Im getting into as far as cost and supply of these parts. I know some cutting will be needed but how do i mount it? Any help and or advice will help. Thanks for reading.

Gil

__________________
97' 1.8TQ
*Hyperboost HXC DV*K03-s(temporary)*Neuspeed Race Springs*
*Bilstein Sport Shocks*Labree HFC*Labree DP*

the bumper should just bolt right up. now if you were gona do a full rs4 conversion, then there would be more extensive work.

__________________

NOOBS CLICK HERE
BT YOUR A4

an OEM RS4 bumper will not bolt right up...its meant for a widebody car so the bumper needs to be modified to fit the A4 lines

__________________
034 GT2871r elim|034 HF Manifold|ATP 3' Inlet Pipe|415cc Injectors|Unitronic Tuned|Revolver Cams|

oh yeah, my bad[8D]

there's plenty of replica bumpers out there that were made for non-widebody tho

__________________

NOOBS CLICK HERE
BT YOUR A4

nice avatar chaos

__________________
S4 bumper in my basement awaiting paint

^^^^^+1 very niceee

__________________
2001.5 Audi A4 1.8tQt
- APR 93/100 octane, Valet&Stock - APR R1 - Custom CAI - H&R Trak+ - Custom HS - B6 CSM - CC Mod - 18" OEM USP 9-spokes - B6 ECP - S4 suspension - VDO - 2500k Fogs - DRF - Kicker L5 - Autotek SS - Passport 9500iX -

Waiting to be installed: Premier F90-BT||PS3||In-Pro Mirrors
WTB: OEM B6 engine cover

alright, so no one has done this before with a rea oem rs4 front that was modified to fit a non widebody a4? what im lookin for is a part list of what ill need to make this happen, and have it look clean.

__________________
97' 1.8TQ
*Hyperboost HXC DV*K03-s(temporary)*Neuspeed Race Springs*
*Bilstein Sport Shocks*Labree HFC*Labree DP*

i have a replica rs4 bumper on my car. it was 25* out when i mounted it so its not on the correct way, but i used two 1/4" bolts in the front cause im gunna have a euro plate soon (or whenever the group buy act. happens haha) and on the side i just used two screws on each side and screwed it into the fender. the bumper feels like it will never move. the only cutting i had to do was to fit the FMIC. i havent done final fitting or body work on the bumper, but it took about 30mins for me to mount it how it is now. if it were the spring, i think i would have taken about an hour and a half to get the whole thing mounted perfect. (minus paint). hope that helps a little. oh and if you DIY, you should really start asking some friends w/ some free time if they can give u a hand, i wouldn't attempt this alone.

__________________
'99.5 1.8TQM

-scat rods
-20mm pistons
-built head
-20psi
-forge 007p
-FMIC

If anyone knows wherei canget a replica one that looks just like the OEM RS4 front bumper other than the gay Reiger one??? i've been wanting to do that to my a4 too.

__________________
the v6 hauls azz...

so nobody knows of anyone with a parts list or description of how they did it themselves? with an OEM RS4 front bumper? has anyone done this state side? ive seen a lot of kits and replicas , but i want the real phukn deal.

__________________
97' 1.8TQ
*Hyperboost HXC DV*K03-s(temporary)*Neuspeed Race Springs*
*Bilstein Sport Shocks*Labree HFC*Labree DP*