my new but used 02 A4
Thread Starter
|
1st Gear
Joined: Mar 2008
Posts: 13
From:
my new but used 02 A4
the car is great, has 50K on it and i got it for 10K because of some problems, so im gana see if i can get any of thoughs problems cleared up right now! When i hit the wrench button on the speedo it says Service! and then goes back, i have scaned it and its not popen any codes, does this mean the ecu wasnt cleared out last time oil change was done?And does this happen everytime an oilchange is needed?! Also every time i break 60MPH it dings at me... can i turn that off? and last but not least, the car didnt come with a manual so how do you program the garage buttons? Thanks for all the help!
Senior Member
Joined: Oct 2006
Posts: 1,556
From:
RE: my new but used 02 A4
I meant a picture of your car, not a picture of the service light.3
To reset the service light, do the following:
- Turn off the ignition
- Then, turn on the ignition again while holding the "wrench" button down. "SERVICE" will appear in the display.
- Press the "0.0" button until the "SERVICE" text is cleared. This display should now show the next service event.
To clear the speed warning:
- Press the "CHECK" button for at least 1 second when the vehicle is moving at a speed above 3 mph. The display will show the warning symbol crossed through to confirm that the speed limit has been cleared.
To program the HomeLink Universal Remote Control, do the following:
- Turn the ignition on. Do not start the engine.
- Press the button for the transmitting channel you wish to use (I), (II), or (III) and keep holding this button down until the LED starts to flash slowly.
- As soon as the LED flashes slowly, release the button immediately. You now have 5 minutes in which to use the handheld transmittier from your original garage door opener to train the HomeLink Universal Remote Control.
- Then take the original handheld transmitter for the garage door opener to the transceiver located in the front bumper of your vehicle (below the right headlight).
What to do at the transceiver:
- Point the garage door opener's handheld transmitter at the bumper below the right headlight. The distance between the handheld transmitter and the bumper should be 0-12 inches.
- Press the activation button on the handheld transmitter and continue to hold it down.
- Observe the emergency flashers on your vehicle. Once programming is successfully completed, the emergency flashers will flash three times (after about 15-60 seconds).
- As soon as the emergency flashers hasve flashed three times, immediately release the button on the handheld transmitter.
(All instructions taken from the owner's manual)
Hope this helps.
To reset the service light, do the following:
- Turn off the ignition
- Then, turn on the ignition again while holding the "wrench" button down. "SERVICE" will appear in the display.
- Press the "0.0" button until the "SERVICE" text is cleared. This display should now show the next service event.
To clear the speed warning:
- Press the "CHECK" button for at least 1 second when the vehicle is moving at a speed above 3 mph. The display will show the warning symbol crossed through to confirm that the speed limit has been cleared.
To program the HomeLink Universal Remote Control, do the following:
- Turn the ignition on. Do not start the engine.
- Press the button for the transmitting channel you wish to use (I), (II), or (III) and keep holding this button down until the LED starts to flash slowly.
- As soon as the LED flashes slowly, release the button immediately. You now have 5 minutes in which to use the handheld transmittier from your original garage door opener to train the HomeLink Universal Remote Control.
- Then take the original handheld transmitter for the garage door opener to the transceiver located in the front bumper of your vehicle (below the right headlight).
What to do at the transceiver:
- Point the garage door opener's handheld transmitter at the bumper below the right headlight. The distance between the handheld transmitter and the bumper should be 0-12 inches.
- Press the activation button on the handheld transmitter and continue to hold it down.
- Observe the emergency flashers on your vehicle. Once programming is successfully completed, the emergency flashers will flash three times (after about 15-60 seconds).
- As soon as the emergency flashers hasve flashed three times, immediately release the button on the handheld transmitter.
(All instructions taken from the owner's manual)
Hope this helps.
