Carburetor Keihin
 

Hi, I need info about how works and how can I fix an Audi carburetor.
Any tips about Keihin carburetor would be a help !
Regards, George

RE: Carburetor Keihin
 

In a nutshell, carburetor works on the Bernoulli's Venturi Principle. In reality it is much more complex especially if you have one of those stupid feedback equipped for emission purposes. Can you fix one, depends on your mechanical skills. What is the problem or symptoms that you are experiencing?

RE: Carburetor Keihin
 

they are very easy to repair, just watch out for springs. also try to get all the tuning bolts as close as they were before. usually they get all dirty inside and all you have to do is clean them up. you will have to buy the gasket kit for your carburator before prosiding. so any more help, I will be glad to assist.

RE: Carburetor Keihin
 

Thanks; my car ( Audi 100 CD 1983/WH 1924cm eats too much gasoline- 14litre/100km. It is a simple one without stupid feedback equipped for emission purposes ( good point). I am not sure that it is very well fixed. And also don't keep revolution constant a relanti. Perhaps it is full of dirty inside but before I will start to dismount I want to have a chart with tuning bolts. I have some skill in this kind of job but I never dismount a carburetor with so many vacuum commands. I suppose that it is better to have more info about this issue.
Regards
George

RE: Carburetor Keihin
 

yes I know lol I even have that book
1 of 2

[IMG]local://upfiles/12092/CD97052137174C4081E52CA153A31461.jpg[/IMG]

RE: Carburetor Keihin
 

#2

[IMG]local://upfiles/12092/099DCA1CA2274954A04EAD47CCF32642.jpg[/IMG]

RE: Carburetor Keihin
 

My friend it is exactly what I need but will you send this information in other format, I can't use if I don't print. Regards George
My email adress is genialul1@yahoo.com

RE: Carburetor Keihin
 

For Offramp
Sir, I successfully change the o-rings from hydraulic pump (only 2 from Hi pressure) with cooper rings. Thanks o lot for your good point. Next week I want to drain out all hydraulic oil and fill with original one.
Have a nice day George

RE: Carburetor Keihin
 

its in jpeg what type do you need to print? and ill email it to you

RE: Carburetor Keihin
 

I have tried all the formats but it doesn't print good because its a photo from my camera and I don't have a scanner, one day ill get one

RE: Carburetor Keihin
 

if you save it to your hard drive you can zoom right in, I didn't realise they wouldn't print out good till you mentioned it[:-]

RE: Carburetor Keihin
 

Sorry my friend, jpeg is fine but I suppose that scanned files will be better. I am not a native English spoken and I prefer to print it and so understand better because in text are many technical terms.
Thanks for your efforts. Best regards George

RE: Carburetor Keihin
 

I got a scanner given:)

RE: Carburetor Keihin
 

data put back because I have more data which ill post shortly

RE: Carburetor Keihin
 

Thanks, you are great. George

RE: Carburetor Keihin
 

any time mate ill just have to get into this scanner thing it takes longer but worth it I suppose;)

RE: Carburetor Keihin
 

My friend, can you give some info about how can I resettle gasoline level in gasoline chamber? It is little strange for me to understand where is the right level.
Regards, George

RE: Carburetor Keihin
 

no problem George there are two types of this carb yours is this one;)
1 of 4

[IMG]local://upfiles/12092/3B48468635C64BF3BD81BD50A2AD434D.jpg[/IMG]

RE: Carburetor Keihin
 

#2

[IMG]local://upfiles/12092/48E67807721741CCA6F8D72FBC194114.jpg[/IMG]

RE: Carburetor Keihin
 

#3

[IMG]local://upfiles/12092/04D2E13F467B40648458D7A6E95B3E27.jpg[/IMG]

RE: Carburetor Keihin
 

#4

[IMG]local://upfiles/12092/A835B0CC76134388B941D9041C7A29B6.jpg[/IMG]

RE: Carburetor Keihin
 

You save my life, thanks. Have you also some info about ignition 0 set? I have some info but it is in German and very hard to understand. Do you know what means DLS?
Have a nice day. George

RE: Carburetor Keihin
 

ignition 0 set ??;)

RE: Carburetor Keihin
 

Sorry, ignition 0 set, means that cylinder 1 is up and get an spark. Sorry, if I don't speak clear in technical terms. Regards George

RE: Carburetor Keihin
 

ahhh right you mean setting the ignition timing up ill have a look in my books it should be there

RE: Carburetor Keihin
 

1 of 1

[IMG]local://upfiles/12092/92BEAD877F9844819A602BB7CA76FA3A.jpg[/IMG]

RE: Carburetor Keihin
 

1 more to come

RE: Carburetor Keihin
 

I put both up because I don't know the exact car and age you have but you can check the engine codes

[IMG]local://upfiles/12092/1921771373544E4BBB2C35523B59B32E.jpg[/IMG]

RE: Carburetor Keihin
 

Audi 100 CD 1983/WH 1924cm second picture;)

RE: Carburetor Keihin
 

setting the timing marks up to the picture puts it to TDC ( top dead center ) then its set for ignition 0 as you say, data is also helpfull if you need to change the timing belt

RE: Carburetor Keihin
 

Nice pictures! Your book is a treasure. Thanks a lot. I have changed the timing belt already... but I need some info about ignition distributor position when the engine is set to TDC. ( don't hurry - my car is on road ) I have found in a German manual some specifications about an engine WH with DLS 18 degrees advance (perhaps in German language and it is a specifications for ignition distributor).
Have a nice day. George

RE: Carburetor Keihin
 

#1 of 1

[IMG]local://upfiles/12092/3D15A2779D5A4BF39BFD05E2AE2E050A.jpg[/IMG]