AudiForums.com
Share Your Pictures with Our Community. Upload Now
0 2018/02/28 00:36:28
0 2018/02/28 00:36:27
In addition, I liked the PSI and Heat rating. It gave me a good feeling due to the higher rating.
In addition, I liked the PSI and Heat rating. It gave me a good feeling due to the higher rating.
0 2018/02/28 00:18:31
This is the JB Weld I like to use due to the workability
This is the JB Weld I like to use due to the workability
0 2018/02/28 00:18:29
Used a flexible Japanese saw to cut off the inlet/outlet as close to the support as possible
Used a flexible Japanese saw to cut off the inlet/outlet as close to the support as possible
0 2018/02/28 00:18:27
Add more JB Weld at the joints for good measure and assurance for a better seal. Let dry for the specified time.
Add more JB Weld at the joints for good measure and assurance for a better seal. Let dry for the specified time.
0 2018/02/28 00:18:25
Apply JB Weld about 1/2" from edge and then insert into large tubing. This will seal the interior of the tubing to prevent leaks.
Apply JB Weld about 1/2" from edge and then insert into large tubing. This will seal the interior of the tubing to prevent leaks.
0 2018/02/28 00:18:23
After about an hour of spinning the smaller diameter tubing on an electric drill to sand off the surface, it finally fit!
After about an hour of spinning the smaller diameter tubing on an electric drill to sand off the surface, it finally fit!
0 2018/02/28 00:18:21
it was hard to make sure the JB Weld was applied all around the joint going to the heater core. Patience is key and using a mirror helps to check. Use a popsicle stick to apply.
it was hard to make sure the JB Weld was applied all around the joint going to the heater core. Patience is key and using a mirror helps to check. Use a popsicle stick to apply.
0 2018/02/28 00:18:19
Both Tubes inserted. Add more JB Weld to the joints to insure a good seal
Both Tubes inserted. Add more JB Weld to the joints to insure a good seal
0 2018/02/28 00:18:15
Before inserting assembled tubing into the inlet/outlet, make sure it will go in about 1.5" - 2". If not you will need to spin the tubing to sand off more surface. Apply JB Weld around the tubing about 1/2" from the edge. Insert and JB Weld will seal the interior of the plastic inlet/outlet tubing.
Before inserting assembled tubing into the inlet/outlet, make sure it will go in about 1.5" - 2". If not you will need to spin the tubing to sand off more surface. Apply JB Weld around the tubing about 1/2" from the edge. Insert and JB Weld will seal the interior of the plastic inlet/outlet tubing.
0 2018/02/28 00:18:13
0 2018/02/28 00:17:18
Advertisement
0 2018/02/28 00:17:01
0 2018/02/28 00:16:53
0 2018/02/28 00:16:35
I used this type of JB Weld due to the workability.
I used this type of JB Weld due to the workability.
0 2018/02/27 23:54:58
0 2018/02/27 23:54:25
I forgot to take a picture of the hoses connected but there is no leak, heater works well, and it's been over a month.
I forgot to take a picture of the hoses connected but there is no leak, heater works well, and it's been over a month.
0 2018/02/27 23:53:38
More JB weld at the joints.
More JB weld at the joints.
0 2018/02/27 23:53:28
Takes longer to cure but the PSI and heat ratings gave me a good feeling.
Takes longer to cure but the PSI and heat ratings gave me a good feeling.
0 2018/02/27 23:53:20
Applied JB Weld about 1/2" away from the edge of the tube. I inserted into the shorten heater core inlet and outlet, the JB Weld seals the walls of the inlet as you insert the tube.
Applied JB Weld about 1/2" away from the edge of the tube. I inserted into the shorten heater core inlet and outlet, the JB Weld seals the walls of the inlet as you insert the tube.
0 2018/02/27 23:52:54
0 2018/02/27 23:52:07
It took about an hour to take off the required amount of surface to fit the smaller tubing into the larger tubing
It took about an hour to take off the required amount of surface to fit the smaller tubing into the larger tubing
0 2018/02/27 23:51:53
Aluminum Pipes assembled and JB Welded together
Aluminum Pipes assembled and JB Welded together
0 2018/02/27 23:49:37
Hacked off broken Inlet and Outlet
Hacked off broken Inlet and Outlet
0 2018/02/27 23:49:13
0 2018/02/27 11:23:11
0 2018/02/27 11:23:08
0 2018/02/27 11:23:06
0 2018/02/27 11:23:04
0 2018/02/27 11:23:02
0 2018/02/27 11:22:59
0 2018/02/27 11:22:56
Advertisement