AudiForums.com
Share Your Pictures with Our Community. Upload Now
the tips and relief cuts, the car is on the ramps and gives you enough rome to install the exhaust system.
the tips and relief cuts, the car is on the ramps and gives you enough rome to install the exhaust system.
0 2008/08/11 11:56:11
The two stock rear mufflers that the remus mufflers replace. (bottom veiw that can be seen from under car. These were polished because it looked cool under the car.
The two stock rear mufflers that the remus mufflers replace. (bottom veiw that can be seen from under car. These were polished because it looked cool under the car.
0 2008/08/11 11:56:11
tip with a slight relief cut in bumper.
tip with a slight relief cut in bumper.
2 2008/08/11 11:48:18
The strait pipes in place of the center resonator.
The strait pipes in place of the center resonator.
0 2008/08/11 11:45:45
One of the Remus mufflers.
One of the Remus mufflers.
0 2008/08/11 11:43:36
0 2008/08/10 01:13:57
The A6
The A6
0 2008/08/09 16:36:11
Boost gauge
Boost gauge
0 2008/08/09 15:40:18
Boost gauge 1
Boost gauge 1
0 2008/08/09 15:40:18
0 2008/08/09 13:17:06
1 2008/08/09 13:17:06
0 2008/08/09 13:16:02
Advertisement
0 2008/08/09 13:16:02
treasure island
treasure island
0 2008/08/09 13:16:02
5. ready for prime , after i let it stay overnight so the glue can bond. still not sure to paint the separator between signal and main lights, black or silver...
5. ready for prime , after i let it stay overnight so the glue can bond. still not sure to paint the separator between signal and main lights, black or silver...
0 2008/08/09 12:42:30
3. i use 3 type of glue (loctite super glue-brush on , j-b weld, and epoxy 5 min) ,blue masking tape. frame is cover because when i glue to don`t mess the whole thing.
3. i use 3 type of glue (loctite super glue-brush on , j-b weld, and epoxy 5 min) ,blue masking tape. frame is cover because when i glue to don`t mess the whole thing.
0 2008/08/09 12:03:44
4. before glue i drill a hole for wires in the corner as you can see, the stip is glue in few points with super glue , and after that get`s a line of blue tape so i don`t get glue on it.
4. before glue i drill a hole for wires in the corner as you can see, the stip is glue in few points with super glue , and after that get`s a line of blue tape so i don`t get glue on it.
0 2008/08/09 12:03:44
this will be an mini-tutorial 1. at that time was only an ideea...
this will be an mini-tutorial 1. at that time was only an ideea...
0 2008/08/09 11:59:07
2. project start , sand frames , and a little math to don`t have things crooked . install the base for led strip to face the road. materials: 1000 grit sandpaper, some frame for walls, to get the angle
2. project start , sand frames , and a little math to don`t have things crooked . install the base for led strip to face the road. materials: 1000 grit sandpaper, some frame for walls, to get the angle
0 2008/08/09 11:59:07
0 2008/08/09 11:25:14
0 2008/08/09 11:24:29
0 2008/08/09 11:24:29
0 2008/08/09 11:24:29
1 2008/08/09 11:18:54
7 2008/08/09 10:05:09
Back Side
Back Side
1 2008/08/09 08:44:14
Front
Front
0 2008/08/09 08:43:20
Front Side
Front Side
0 2008/08/09 08:43:20
Side
Side
0 2008/08/09 08:43:20
my headlight before, 8k hid install
my headlight before, 8k hid install
0 2008/08/09 06:33:07
led project
led project
0 2008/08/09 06:28:03
01 a6 2.8Q
01 a6 2.8Q
0 2008/08/09 06:28:03
Advertisement