Computer & Fuel Systems Talk about the computer, fuel systems and delivery, customization and more.

Cheap power, Diode, MBC, and Boost gauge install

Thread Tools
 
Search this Thread
 
Old Jul 24, 2007 | 05:10 PM
  #21  
Stuntman's Avatar
1st Gear
Joined: Feb 2007
Posts: 88
From:
Default RE: Cheap power, Diode, MBC, and Boost gauge install

No it wouldnt. Pre 00 aeb motors dont have MAP sensors.
 
Old Jul 24, 2007 | 05:41 PM
  #22  
pimptrooper3000's Avatar
Senior Member
Joined: Apr 2007
Posts: 210
From:
Default RE: Cheap power, Diode, MBC, and Boost gauge install

dam...so there is nothing i can do to do this or something similar???
 
Old Jul 25, 2007 | 07:40 PM
  #23  
vassar007's Avatar
1st Gear
Joined: May 2006
Posts: 88
From: NY
Default RE: Cheap power, Diode, MBC, and Boost gauge install

Yeah, but if I use APR software and then use a boost controller, won't I run lean unless I find a way to get more fuel into the engine?

Thanks bro,

JPF
 
Old Jul 25, 2007 | 08:13 PM
  #24  
Bondga's Avatar
Senior Member
Joined: Aug 2006
Posts: 1,159
From:
Default RE: Cheap power, Diode, MBC, and Boost gauge install

no, thats what this mod is for. it keeps the map from seeing whats going on so that the maf can adjust your fueling to keep you stoich
 
Old Jul 25, 2007 | 08:38 PM
  #25  
Karl's Avatar
Administrator
Joined: Dec 2004
Posts: 8,981
From: Seattle, WA
Default RE: Cheap power, Diode, MBC, and Boost gauge install

First one to blow their engine after doingthe diode mod wins
 
Old Jul 25, 2007 | 08:48 PM
  #26  
Bondga's Avatar
Senior Member
Joined: Aug 2006
Posts: 1,159
From:
Default RE: Cheap power, Diode, MBC, and Boost gauge install

haha i dont see it happenin, once i get my new maf i'll put up some a/f charts
 
Old Jul 25, 2007 | 09:10 PM
  #27  
Karl's Avatar
Administrator
Joined: Dec 2004
Posts: 8,981
From: Seattle, WA
Default RE: Cheap power, Diode, MBC, and Boost gauge install

this will remove the over boost safety that the map sensor is used for, this means if you over boost for any reason it might cause major engine damage.

the ecu can NOT adapt afr under full load. The ecu is not adjusting injector pulse width off the primary o2 sensor voltage at this point. Also the lower load value will result in an incorrect base timing value that the ecu may not be able to compensate for.
 
Old Jul 25, 2007 | 09:24 PM
  #28  
cincyTT's Avatar
Thread Starter
|
I'm make believe
Joined: Dec 2006
Posts: 17,587
From: In my head
Default RE: Cheap power, Diode, MBC, and Boost gauge install

wondered why my nuts were hanging so low lately, i looked down, HEY KARL!

There is nothing wrong with this method. I stand by what i have said 100 times already. Im not buying a chip for my stock turbo when i go back to BT. Makes no sense.
 
Old Jul 26, 2007 | 12:31 AM
  #29  
vassar007's Avatar
1st Gear
Joined: May 2006
Posts: 88
From: NY
Default RE: Cheap power, Diode, MBC, and Boost gauge install

Wow, this actually seems doable. I'm hoping to get it set up in New York when I return. My plan is to do this, but to be really really careful with how much boost I run. Probably try it with just a pound or two more than APR's software allows gradually building up to the figures CINCY gave.

Best,

JPF
 
Old Jul 26, 2007 | 12:39 AM
  #30  
cincyTT's Avatar
Thread Starter
|
I'm make believe
Joined: Dec 2006
Posts: 17,587
From: In my head
Default RE: Cheap power, Diode, MBC, and Boost gauge install

if you have a chip you dont need to do this. This is a chip alternative. If you have a chip just up the boost to 20psi and your good.
 



All times are GMT -4. The time now is 01:17 AM.