cam problem
Thread Starter
|
1st Gear
Joined: Jul 2008
Posts: 143
From: norway
now i have got the car back from the autoshop. there was onely a bad timeing on the intake cam on the right side.. strange.. will change the gaskets on the top's,install the bumper.,and hit the roads again and make them unsafe again:-)
so now i hope there will be no more trouble.:-)
so now i hope there will be no more trouble.:-)
JK.
Thread Starter
|
1st Gear
Joined: Jul 2008
Posts: 143
From: norway
yes,but i got it wrong. the mechanic from audi told me wrong too so when i changed the seals yesterday, i saw that i had missed one tooth. i had it at an non audi dealer and they got it right:-)
all the problems cost me little more money for some extra parts(that i did not need) but now i am happy thats ok. i can just sell the extra parts(chain tensioner,intake cam).
tnx for all the help guys!
all the problems cost me little more money for some extra parts(that i did not need) but now i am happy thats ok. i can just sell the extra parts(chain tensioner,intake cam).
tnx for all the help guys!
Last edited by beemerfanatic; Jan 22, 2009 at 01:32 AM.
1st Gear
Joined: Mar 2008
Posts: 8
How much for the tensioner? I think I may have a bad tensioner in my 2.8.
My intake cam on the left side of the engine has the same alignment problem you had. My engine runs fine, but there is a rattling noise on the left side. I plan to turn the cam one tooth to align the marks.
My intake cam on the left side of the engine has the same alignment problem you had. My engine runs fine, but there is a rattling noise on the left side. I plan to turn the cam one tooth to align the marks.
Thread Starter
|
1st Gear
Joined: Jul 2008
Posts: 143
From: norway
my tensioner is for the right side..so i cant help you there..Dont think it's the same on both sides.
if you have a rattling noice,maybe the plastic on the top/bottom of the tensioner is bad? if you turn one tooth the engine will not run fine..!
i have tryed several times with no luck. my last option was a mechanic,and the bastard did it right. c",)
if you have a rattling noice,maybe the plastic on the top/bottom of the tensioner is bad? if you turn one tooth the engine will not run fine..!
i have tryed several times with no luck. my last option was a mechanic,and the bastard did it right. c",)
1st Gear
Joined: Dec 2008
Posts: 9
OK, gentlemen, sounds like I have a similar problem with my A8. It' has low vacuum at idle (7 - 8 in Hg) / rough idle, has multiple misfire codes on Bank 2, (cylinders 5, 6, 7, & 8) . So it has horrible low speed performance, but runs like it's got a 'Hot' cam. Once the revs reach about 3000, it bursts with power, but low torque down low. I assumed it was an incorrect timing issue from the previous owner not doing a proper job on the timing belt change, but not sure where to start. Because there are no other codes except for the 5, 6, 7 & 8 misfires, does that tell me it is the timing belt that is off, or the bank 2 chain that is mistimed?
3rd Gear
Joined: Nov 2007
Posts: 1,980
From: Northern California
OK, gentlemen, sounds like I have a similar problem with my A8. It' has low vacuum at idle (7 - 8 in Hg) / rough idle, has multiple misfire codes on Bank 2, (cylinders 5, 6, 7, & 8) . So it has horrible low speed performance, but runs like it's got a 'Hot' cam. Once the revs reach about 3000, it bursts with power, but low torque down low. I assumed it was an incorrect timing issue from the previous owner not doing a proper job on the timing belt change, but not sure where to start. Because there are no other codes except for the 5, 6, 7 & 8 misfires, does that tell me it is the timing belt that is off, or the bank 2 chain that is mistimed?
